MEGO Node
MEGO Node (WiFi MCU Development Board)
คู่มือการใช้งานบอร์ด MEGO กับ LINE Service ดาวน์โหลดได้ที่นี่ (อัพเดจ 06-2018)
http://ftp.qwavesys.com/repository/MEGO_MEGO-Node/MEGO-Node LINE-Service Getting-Start 1.0.0-Amornthep.pdf
หนังสือ คู่มือการใช้งาน MEGO Book เวอร์ชั่นล่าสุด ดาวน์โหลดได้จากที่นี่ (อัพเดจ 06-2018)
http://ftp.qwavesys.com/repository/MEGO_MEGO-Node/MEGO_Book__0.2_73pages_Amornthep.pdf
ตัวเลือกสินค้ามี 2 ชนิด
1.บอร์ด MEGO Node (Model A) - ไม่มีวงจร ADC = 690 บาท
2.บอร์ด MEGO Node (Model ฺB) - มีวงจร ADC 16bit จำนวน 4 Ch = 790 บาท
(*สินค้าหมด ไม่มีกำหนดผลิตเพิ่ม แต่ถ้าต้องการจำนวน 100 ชิ้น ขึ้นไปติดต่อสั่งผลิตได้)
รายการสินค้าที่จะได้รับ
1.บอร์ด MEGO Node = 1 บอร์ด
2.สายอากาศ WiFi ย่าน 2.4 GHz แบบ IPEX 4dBi แบบ U.FL Connector = 1 ชิ้น
3.แผ่น DVD (5GB) โปรแกรม LabVIEW 2014 และ LabVIEW 2017 (*เวอร์ชั่นทดลองใช้) = 1 แผ่น
4.สาย USB Cable (Full Speed 2.0) ความยาว 30 cm =1 เส้น
5.Pin header 15 pin = 2 ชิ้น (*ขนาดพิเศษ มีความยาวมกกว่ากว่าปกติ)
6.Pre-Programed โปรแกรม Demo เพื่อเชื่อมต่อ บอร์ดกับ MEGO LINE Service ควบคุมการทำงานผ่าน WiFi ได้ทันที คู่มือการใช้งานดาวน์โหลดได้ที่นี่
The MEGO Node is 32 bit microcontroller development board perfect for the prototyping & learning embedded systems. It has 11 Digital I/O, 4 Analog Input (16 bit), I2C, SPI and Serial and WiFi 2.4GHz capabilities.
At its heart, the Espressif ESP8266 WiFi SoC “WROOM-02U” module. It is FCC, CE, TELEC, Wi-Fi Alliance, and SRRC certified module with an onboard antenna.
Espressif System's WROOM-02U is a low cost WiFi SoC with integrates a U.FL connector., A 32-bit low power micro-controller with CPU clock upto 160MHz, 50KB of user available RAM and an external 2MB of Flash memory with a full WiFi front-end (both as client and access point).
MEGO Node Specification
- Espressif MCU 32 bit upto 160 MHz (WROOM-02U)
- WiFi 2.4GHz , Memory Flash 2MB, RAM 50k
- 4 Analog Input (A0-A3), 16 bit ADC (3.3V) ADS1115 16bit 4-Ch Delta-Sigma ADC With PGA (*Optional for Model B)
- 11 Digital (3.3V) I/O (D0-D8,TX,RX) Supported (I2C,SPI,1-Wire,DHTxx,SoftSerial,SoftI2C)
- Onboard Power regulator 3.3V 1A ,Supply Input VIN = 5V-15V
- Power +5V via USB port for programming and debugging.
- Onboard USB debug and programming (Speed 921600 buad)
- Dimension 49 x 24.5 x 13mm
MEGO Node Layout
- 1.Espressif MCU WROOM-02
- 2.Antenna WiFi Connector U.FL 2.4GHz
- 3.LED Pin16 (GPIO)
- 4.USB UART Bridge Silicon Labs CP2104
- 5.Reset Button Switch (SW1)
- 6.Micro USB Connector (Programming&Debug)
- 7.User/Config Button (SW2)
- 8.GPIO Port 1
- 9.GPIO Port 2
LED Status
Pin Definition
Software Development Tool
In addition, The MEGO Board can be programmed using established development tools, such as Arduino IDE (C/C++), LabVIEW (MEGO Q-WAVE Library), Python (uPython).
1.เขียนโปรแกรมด้วยภาษา LabVIEW (เวอร์ชั่น 2014 หรือ 2017)
ภาพตัวอย่าง LabVIEW MEGO Library เวอร์ชั่นล่าสุด
ตัวอย่าง LabVIEW MEGO Example Code ที่มาพร้อมกับ MEGO Driver
2.เขียนโปรแกรมด้วยภาษา C/C++ (Arduino IDE)
ติดตั้ง Arduino IDE แล้วเพิ่ม Board Package ตามลิงค์นี้
https://github.com/QWaveSystems/Mego-Arduino/releases/download/package/package_mego_index.json
ชื่อ Board Package คือ "Mego Arduino by Qwave Community"
การใช้งานให้เลือกบอร์ด "MEGO Node" และสามารถเลือก Upload Speed ได้สูงสุด 921600 buad
Schematic (OSHW)
PCB Layout (OSHW)
Download
ไฟล์ต่างๆ ดาวน์โหลดได้จาก Github
https://github.com/QWaveSystems/MEGO_Node
ไฟล์ต่างๆ เกี่ยวกับบอร์ด MEGO และ MEGO Node ดาวน์โหลดตรงจาก Server Q-Wave
http://ftp.qwavesys.com/repository/MEGO_MEGO-Node/
ตัวอย่างโปรแกรมเขียนด้วย Arduino IDE (C/C++) อ่านค่า เซนเซอร์อุณหภูมิ DS18b20
http://ftp.qwavesys.com/repository/MEGO_MEGO-Node/Mego_Arduino_DS18B20_8ch.zip
MEGO LINE Service
การใช้งานบอร์ด MEGO Node ร่วมกับ MEGO LINE Service ดาวน์โหลดคู่มือการตั้งค่าใช้งานได้ที่นี่
http://ftp.qwavesys.com/repository/MEGO_MEGO-Node/MEGO-Node LINE-Service Getting-Start 1.0.0-Amornthep.pdf
MEGO Node (Model A) - Without ADC |